You can find the results of your search below. If you didn't find what you were looking for, you can create or edit the page named after your query with the appropriate tool.


electronics:wr703n:openwrt: 8 Hits
last option in the left bar (DateTimeCfgRpm.htm) then on the thrid sub-option (SoftwareUpgradeRpm.htm).... page will become unavailable. Wait a bit further then reboot the device with the power plug. The led should blink for a short while and then settle on. You should now be able to log to the r... ing command: nmcli dev list | grep 'IP4.*DNS' Then restart the network with /etc/init.d/network re
linux:cnc: 7 Hits
USB adapter. It was seen as an external USB drive then. Using ''fdisk'', I re-partitioned the disk to 3... he system to install (and future home if needed) Then ''unetbootin'' allowed me to install linuxcnc on ... k to the (control-alt-F7) and retry. If it fails, then you'll probably have to find a CDROM. For the fu... u - mkswap -c /dev/sda2 swapon /dev/sda2 But then I switched to a shorter path: installed a alterna
electronics:wr703n:unbricking: 6 Hits
the bottom part of the FTDI board. Run minicom, then unplug/plug the miniusb, you should see the bootl... mho), run it in the foreground only for updating, then kill it with Control-C when done: in.tftpd --foreground --verbose Then copy the binary you want to flash to the device i... ink down'' and the many ''T'' timeout indicators? Then make sure that your WR703N is connected with a ca
electronics:wr703n:relay: 6 Hits
following as ''/etc/init.d/wifi_idle_shutdown'', then make it executable with ''chmod +x /etc/init.d/wi... er when going to die (2-minute shutdown time) * then off when the device is dead (obviously) <code ba... BL.*192\.168\..*sport=22" /proc/net/nf_conntrack; then # No SSH connection - slowly blink and count t... 100 if [ "$elapsed" -gt "$delay_before_off" ]; then # After some time, check if wifi really was u
wiki:syntax: 4 Hits
[doku>config]] file. Hint: If DokuWiki is a link, then it's enabled. * When a section's heading is cha... a filename that is not a supported media format, then it will be displayed as a link instead. ==== Fal... ay we should > Really? >> Yes! >>> Then lets do it! I think we should do it > No we sho... >> Well, I say we should > Really? >> Yes! >>> Then lets do it! ===== Tables ===== DokuWiki support
electronics:raspi: 3 Hits
t's do it separately ===== Stream ===== We will then stick on with an intermediate /tmp/stream folder then, as described [[## /volatile tmpfs size=25M,mode=0777 0 then mount it sudo mkdir /volatile sudo mount /vol
electronics:wr703n:webcam: 2 Hits
d checked that it was recognized with ''cheese''. Then I dumped the system log with ''dmesg''. The last ... gave me better images but still unusable data. I then used ''--set gamma=80%'' which gave me something
electronics:wr703n:sdcard: 2 Hits
the disk (if ''mount'' tells you i t is mounted, then ''umount'' it first) * use ''fdisk /dev/sdh1''... the SD card for additional storage memory ===== Then set the SD card to replace the internal flash sto
electronics:wr703n:webservice: 2 Hits
of 80 in the file ''/etc/conf/uhttpd'' into 8080, then restart the service with ''/etc/init.d/uhttpd res... 0, eg [[|]] then I am granted with the main lua script (which may
electronics:raspi:archlinux: 2 Hits
nce before/after plugging it in: sudo fdisk -l Then transfer the system with ''dd'' (where DEVICE= /d... ile mkswap /swapfile swapon /swapfile </code> And then to make it permanent: echo '/swapfile none swap
electronics:wr703n:nohup: 1 Hits
metimes extremely useful: opkg install screen Then check
linux:cron: 1 Hits
f -x "$(basename $0)"); do if [ $pid != $$ ]; then exit 1 fi done on your scri
electronics:wr703n:cgi: 1 Hits
sis, just add server.modules += ( "mod_cgi" ) Then, the server must be told not to serve the executa
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
Recent changes RSS feed Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki